Oelabs Inc Montreal, Alberta

We are offering Fgm Optical Fiber Geometry Analyzer(upgraded for Speciality Fiber). Model no: fgm-rs-5 fgm optical fiber geometry analyzer is a new product after ofm optical fiber multiparameter testing system developed by rayscience .it can be used to replace the expensive imported machine. The equipment is based on grey calibrate technique of eia/tia fotp176.it is a high-precision intelligent instrument consisting of advanced optical system , ccd camera, computer and so on . Perfect software has been designed to calculate precisely all data collected from the optical fiber’s near field figure. The instrument can obtain the boundary of fiber cladding and diameter of core, at the same time it can provide all the geometry parameters .test result is precise and reliable.

• Brand Nameoelabs

We are offering Integrated Optic Chip for Gyroscope (y Waveguide Modulators). model: ioc-15-09-80-n 1550nm integrated optical chips (y waveguide) with 80l165um pm fiber, 1m fiber length, without connector input: 125l250um pm fiber, output model: ioc-13-09-09-n 1310nm integrated optical chips (y waveguide) inputloutput:125l250um pm fiber, 1m fiber length, without connector model: ioc-13-09-80-n 1310nm integrated optical chips ( ywaveguide) input: 125l250um pm fiber, output with 80l165um pm fiber, 1m fiber length, without connector model: ioc-15-09-09-n 1550nm integrated optical chips ( y waveguide) inputloutput: 125l250um pm fiber, 1m fiber length, without connector features of integrated optical chips : x-cut, y-propagating linbo3 very low insertion loss. ape process for waveguide, works in single polarization high extinction ratio fiber is sloping coupled with waveguide, which deduce optical return far and away push-pull electrode design may deduce half wave voltage small packaging and lightweight excellent long-term stability applications： it is for attitude control of movements such as airorafts, ships, guided missiles, automobiles eto in the fiber gyroscope system, hydrophone and other optic sensitive fields. faraday effect was used to measure current through fiber circuit in the current sensing system. operation instructions a)if the devices work under the single state of polarization, the polarization state of input light must conform to devices. b)avoid the electrical damage of the devices;the electrode voltage of modulators should be lower 30v. c)applying too much force to fiber may cause it broking easily. avoid drawing twisting.bending radius must not be less than 30nm. d)avoid too much force between metal tube and fibers. put up the tube and the fibers together when using it. avoid bending at the joint ofthe tube and the fibers. e)storage environment humidity must be less than 50%, and not contain the materials which damages devices. f)avoid the devices suffering from intense thermal shock and inhomogeneous by heated g)avoid stressing to the joint of the fiber connection circuits.

• Brand Nameoelabs

We are offering Phase Modulator. Mode|:pms15 1550nm phase modulator(straight waveguide) model: pms13 1310nm phase modulator(straight waveguide) phase modulator schematic: linbo3 phase modulator, made with the proton exchange or tiindiffusion method. Lt features low insertion loss, low drive voltage, low back reflection, wide wavelength range, and high efficiency. It is ideal for optical chirp control in high speed fiber communication systems, high-speed phase control for sensor systems, phase shift key modulation for coherent communication systems, optical frequency shifting for measurement systems, and stimulated brillouin scattering (sbs) reduction for analog fiber optic systems. We can provide different pigtail and package by customer requirement. for more information on this or other products and their availability, please contact us directly.or view our homepage

• Brand Nameoelabs

We are offering Quadrupolar Fiber Coil Winding Station/acws-230d Automated Coil Winding Station. Introductions of quadrupolar fiber coil winding station: a comprehensive fully automatic winding station is required to precisely wind optical fiber to manufacture ifog coils for tactical & strategic grades .in order to improve this working yield, acws-230d is developed which winding machine and unwinding machine is separate. The machine is for making coil outer diameter ≤200mm and fiber coating diameter ≤0.5mm, and the total fiber winding length is ≤5km. The fiber coil is winding by the method of quadrupolar patter or continuously straight winding fiber coil. Features: 1. The machine enable product spool automatically winding and displacement.both ends of fiber can be swapped freely. 2. Custom-made winding process, including fiber coater diameter, master spool winding slot width and product spool slot width and required tension and etc. 3. Fiber coating diameter programmable precision: 0.001mm 4. Master spool winding slot width and product spool slot width programmable precision: 0.001mm 5. Splitting axis precision: 0.01mm 6. Splitting axis repeatability position precision: 0.003mm 7. Adjust fiber tension level within resolution of ±2g ; rather stable in the support of closed-loop tension controller. 8. Fiber total length programmable precision: 0.1m ( resolution of ±0.3%) 9. While in winding, the fiber on master spool will be discharged automatically 10.2 unwinding functions available , one is stopping to unwinding during winding of the fiber ; the other is to unwinding for the whole layer 11. Automatically collecting this fiber during un-winding the fiber 12. Locate this zero-point for this main axis and splitting axis 13. Optional: vision system are built for inspecting this whole winding process(just for inspecting, not for controlling the progress connected with winding machine) option introductions: 1. Industrial vision system and illumination device in order to keep the coil winding well，it should be equipped with industrial vision system with fivevisual adjustable device and assistant illumination device which operation is by manually. It adopted the remote switches controlling for the assistant illumination device. The ccd system can be amplified 20-100times, it facilitate the fiber winding inspecting clearly and easily. It substantially save the manpower and improved the quality . 2 dynamic length meter this device is built-onto the winding machine, it can write the length of the coiled fiber for current layer of the winding bobbin . Its precision can reach ±0.3%; it’s very convenient to record the actual length of the coiled fiber . 3.epoxy delivery system in order to make a good fiber coil, there are two installations for epoxy delivery with temperature controller onto the right or left displacement, which is adjusted by manual. The epoxy delivery system is built-into heating device and temperature controller, which is to heat the glue and keep it at the exact working temperature. Also it can it can reduce the viscosity of colloid .and to glue symmetrically there are two switches and temperature-controller for controlling epoxy delivery onto the main controlling panel. The heater and motor can work when the switch is on, when the switch is off, its heater and motor can be cutting off. 4. Ultraviolet solidify lamp in order to make this winding well, there is a uv lamp built-into two dimensions stages onto the top of winding machine, which is adjusted by manual. The uv lamp can be activated via remote-control. 5.ultraviolet protective cover in order to avoid hurting the workers when operating the ultraviolet solidify lamp, put down the window shade and cover the gluing device with ultraviolet cover before turning on the ultraviolet solidify lamp, then turn on the ultraviolet solidify lamp with remote control switch and timing, turn off the ultraviolet lamp after timing then do other operation.we can make other optional accessories on request. It is welcomed that you tell us your detailed requirements.view our homepage.

• Brand Nameoelabs

We are offering Octupole Fiber Coil Winding Station/Automatic Fiber Coil Octupole Winding Station. Model no:acws-200b acws-200b fiber coil winding station is a newly-released machine which can wind the fiber coil for fogs in the method of cw straight or any other ways like octupole winding, dipole winding and etc. Its fiber coil outer diameter is ≤200mm, and its fiber coating diameter is ≤0.5mm, total fiber winding length is ≤3km features of octupole fiber coil winding station: 1.manual operation should be necessary for installation the fiber transition spool and fiber delivery. automatic operation is done for product spool fiber winding, automatic splitting, automatic change for fiber transition spool at both side, automatic crossing change and etc. 2.per customer own requirement, programme can be made for automatic winding, automatic splitting, automatic change and automatic crossing change at any winding method. 3. Winding programme can be custom-made for fiber outer diameter, product spool diameter, transition spool diameter and required tension . 4. Fiber outer diameter programmable precision: 0.001mm 5. Transition spool winding slot and product spool slot width programme precision: 0.01mm 6.splitting axis splitting precision: 0.01mm 7. Splitting axis repetition position precision: 0.005mm 8. Incorporated into closed-loop tension controller, fiber tension is very stable while winding ( variation: setting ±1.5g). Actual tension is 1/6 of setting data. 9. Total fiber length programme precision: 100m, (variation: setting ±0.5%). 10. Fiber from transition spool is automatic delivery while winding the fiber coil. 11. Automatic unwinding 2 methods are available, one is to first stopping while winding, then unwinding. The other is to unwinding for the whole layer. 12. Automatic fiber collecting is available while it is in unwinding. 13. Automatic zero-finding is available for main axis and splitting axis programme. 14. Tension alarm for over and off the limits is available. 15. Fiber broken protection set-up is available. 16. Automatic fiber coil compensation is available. 17. Designing method: transition spool can automatically cross and change compared to the conventional quadrupolar winder which transition spool is unchangeable. It can be winding the fiber coil at any method with direct winding, dipole winding, quadrupole winding, octupole winding and hexadecapole winding , cross winding and cross-free winding and etc. Main parts for winding station： 1.driving device for accumulating wire spool. The device is very lightweight since it is acted as passive interchangeable part.it is comprised of accumulating wire spool fixature, pay-off active device and coordinated transposition position. 2、system for closed-loop tension and coordinated transposition position. For accumulating wire spool 3、controlling chassis for main frame： the special main controlling system is for 10 axis controlling, it keeps strong/weak current departed. 4. Fivevisual driving device the device can support precise moving and position at x/y/z ( advanced servo motor+precise ball screw+ bearing are built-into) and rotating movement on the left/right platform. it can satisfy the accumulating wire spool departure, movement, interchange and building while coordinated transposition. 5.precise main axis and servo-driving 2 sets of precise main axis are built-onto the winding station, which can support higher rotation precision. Driving is built with advanced servo-motor and planet gear reducer, which can support the runing balance and précising. 6.main controlling panel. It is designed by 10” touchable screen, which is easy to read. 7. Industrial vision system and illumination device in order to keep the coil winding well，it should be equipped with industrial vision system with fivevisual adjustable device and assistant illumination device which operation is by manually. It adopted the remote switches controlling for the assistant illumination device. The ccd system can be amplified 20-100times, it facilitate the fiber winding inspecting clearlyand easily. It substantially save the manpower and improved the quality . We can make other optional accessories on request. It is welcomed that you tell us your detailed requirements.view our homepage.